. Cordless Drill MODEL 6043D I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. M a k i t a t o o l s. Electrical Safety 4. A battery operated tool with integral bat- teries or a separate battery pack must be 6043D 10 mm (3/8”) 4.5 x 20 mm (3/16” x 3/4”) 450/min. 201 mm (7-7/8”) 0.84 kg (1.9 lbs).
recharged only with the specified charger for the battery. A charger that may be suit- able for one type of battery may create a risk of fire when used with another battery. Use battery operated tool only with specif- ically designated battery pack. Keep hands away from rotating parts. Do not leave the tool running.
Operate the tool only when hand-held. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. (1) battery charger, (2) battery, and (3) product using battery. CAUTION - To reduce risk of injury, charge only MAKITA rechargeable Other types of batteries may burst caus- ing personal injury and damage. Do not expose charger to rain or snow. Do not charge the tool when temperature is BELOW 10°C (50°F) or ABOVE 40°C (104°F). Do not attempt to use a step-up trans- former, an engine generator or DC power receptacle.
Do not store the tool in locations where the temperature may reach or exceed 50°C (122°F). FUNCTIONAL DESCRIPTION 002059 1.
Charging plug 002072 1. Switch trigger 002085 1. Reversing switch CAUTION:. Always be sure that the tool is switched off before adjusting or checking function on the tool. Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Always be sure that the tool is switched off before carrying out any work on the tool.
Installing or removing driver bit or drill bit Hold the ring and turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. DISPOSING OF TOOL A Ni-Cd battery is built into the handle of the tool. It can explode in a fire or toxic materials can leak out of it. Recycling the Battery The only way to dispose of a Makita battery is to recycle it.
The law prohibits any other method of disposal. To recycle the battery: 1. CAUTION:.
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons.
Only use accessory or attachment for its stated purpose. First-Class Postage Required Post Office will not deliver without proper postage.
Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA Fold. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog 4. Most favored points are: Design Features Size Price Makita Brand MODEL NO.
YEAR SERIAL NO. PHONE 20-29 30-39 40-49 Paste Paste Radio Exhibition. Date Purchased When you need service: Send complete tool (prepaid) to one Dealer’s Name & Address of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center. Be sure to attach a letter to the outside of Model No. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
. Cordless Driver Drill INSTRUCTION MANUAL SPEC IF I CAT IONS C d p a c i t i c s Wood Wood screw Stcel 5 m m mini 11111, a'!
13'16' x 3 4'1 7000 Model DC7100 Fast Charger Battery Cartridge 5 0 H r Manufacturer reserves t h e right t o c h a n g e specifications without notice. SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. B e sure switch is OFF when plugging in. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord 9.
Do not operate charger with damaged cord or plug mediately. Do not operate charger if it has received a sharp blow, been dropped, or other- wise damaged in any way. ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C ( 5 O O F ) ABOVE 4OoC ( 1 0 4 O F ).
Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. Installing or removing battery cartridge 0Always switch off the tool before inser- tion or removal of the battery cartridge.To remove the battery cartridqe, pull out the set plate on the bottom i f the and grasp both sides while withdrawing from the barrel. Selecting correct Phillips bit Use the chart to determine the best size driver bit for the size of screw wish use. Selecting slotted bit Use a slotted bit that properly fits the screw slot. Use of a bit t h a t is too small will damage the screw and/or bit. CAUTION: Before inserting t.e battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns t o the 'OFF' position when released.
Reversing switch action This tool has a reversing switch to change the direction of rotation. Bubble level tool is equipeed with a bubble level to This aid in holding the tool horizontally. Simply center the bubble in the sight window. Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool.
Tool Start the slowly and then increase the. Drilling operation Drilling wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece.
Drilling in metal To prevent the bit from slipping when starting a hole, make a centerpunch and hammer at the point to be drilled. Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection T o maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Part 7 4 3 4 0 1 - 6 Foam polishing pad Part N o. 7 4 3 0 2 3 - 2 with your Makita tool specified in this Fast charger Model D C 7 1 0 0 113109-0 Part No. Battery holster Holster holds extra battery Part N o. 823033-3C Steel carrying case Part N o. 823087-3 (Steel case) Part N o.
181372-3 (Plastic Case) Tool holster has some bits storage space Use holster carry drill o n l y removing bit. (3/8') CORDLESS DRIVER DRILL Model 6071D Note: The switch and other part configurations may differ from country to country. MOUEL 6071U 'EM A&, DESCRIPTION Drill Chuck S10 Pan Head Screw M 5 x 1 8 Gear Plane Bearing Motor Holder S w m h Housing Bubble Level Note T h e switch and other speclflcalions part,!. ONE YEAR from the date of original purchase. Should any troubkdevelop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
If inspection shows the trouble is caused by defective workmanship replace) without charge.
. Cordless Driver Drill Equipped with Electric Brake (3/8') MODEL 60930 (3/8') MODEL 6093DW With Fast Charger INSTRUCTION MANUAL SPEC IF I CAT1 0 N S Model 6093D Capacities No load speed Dimensions weight x W x Steel Wood Wood screw. IMPORTANT SAFETY IN STRU CTlO N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING.
Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. Before using battery charger, read all instructions and cautionary markings o n (1) battery charger, (2) battery, and (3) product using battery. CAUTION To reduce risk of injury, charge only MAKITA Battery 7000, 9000 or 9100. Other types of batteries may burst causing personal injury and damage.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 1 0 ° C (5OOF) ABOVE 4OoC (104OF). Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.
Installing or removing battery cartridge tool before insertion or removal of the battery cartridge.Always switch off the.To remove the battery cartridge, pull out the set plate on t h e tool and grasp both sides of the cartridge while withdrawing it from the barrel. If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Installing or removing drill bit or driver bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing removing the bit. Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger.
Release the trigger t o stop. CAUTION: Before inserting the battery cartridge into the tool, always check to see t h a t the trigger switch actuates properly and returns t o the 'OFF'. Adjusting fastening torque The fastening torque can be adjusted in six Adjusting ring -7 i stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the.
NOTE: Use the proper bit for the head of the screw that you wish to use. Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. When driving wood screws, predrill Pilot Nominal diameter of Recommended size holes to make driving easier and to pre. Take the battery Makita Authorized Center as a Makita Distributor that been designated battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under 'Tools Electric.
The Theory of Poker. David Sklansky. Logic of poker, the book will. The Theory of Poker is an expansion and total revision of the book Sklansky on. David sklansky pdf.
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool.
CAUTION: attachments are recommended for use with your Makita tool specified in this These accessories manual. 25-'86 EN 10 mm (318') CORDLESS DRIVER DRILL Model 6 0 9 3 D Note: The switch and other part configurations may differ from country to country.
6093D Dec -25-'86 MODEL ' i M ' i M DESCRIPTION DESCRIPTION Washer 1 4 Pan Head Screw M 4 x 2 2 lWllh Washer Flat Ball Bearing 626LLB Head Screw M 4 x 3 5 IWtth Washer1 Flat Washer. MAKITA LIMED O N E YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o ONE YEAR be free of defects from workmanship and materials for the period of.
.:.:f,. Equipped with Chuck and Electric Brake Keyless MODEL 6 O l l D MODEL 6011DW Wlth Fast Charger INSTRUCTION MANUAL SPECIFICATIONS Model 8011D Capacities No load speed IRPMI Dimensions 1 1 x W x HJ weight Steel. IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite injuries. WORK CONSIDER AREA ENVIRONMENT. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. AVOID UNINTENTIONAL STARTING.
Makita Cordless Tool Kits
Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging 16. 1200, CAUTION To reduce risk injury, charge only MAKITA Battery 1 2 1 0, 9000 9100.
Makita Drill Manual
Other ty,pes of batteries may burst causing personal injury and damage. Do not expose charger t o rain or snow. I::.,r.ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 4OoC ( 1 0 4 O F ).
Batteries For Makita Cordless Drill
battery Installing or removing cartridge.Always switch off the tool before insertion or removal the battery cartridge.To remove the battery cartridge, pull out Set plete the set plate on the tool and grasp both sides of the cartridge while withdrawing from the tool. Installing or removing driver bit or dirll bit CAUTION: Always be sure that the tool i s switched off and the battery cartridge i s removed before installing or removing the bit. Hold the ring and turn the sleeve counter- clockwise to open the chuck jaws.
Speed change To change the speed, turn the speed change knob 180' while the tool is running. Be Speed change knob sure that the speed change knob is turned 450 Rlmin. To the correct speed setting before you 1,350 Rlmin.
![]()
Begin operation. Always be sure that the tool is switched off and the battery cartridge removed before attempting to perform inspection or maintenance.
Maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACC ESSO R I ES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. F e b - 0 4 - ' 9 2 CORDLESS DRIVER DRILL Model 6011D. SEQUENTIAL DAMAGES FROM THE SALT OR USE O F THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THETERM O F THIS WARRANTY.
MAKITA DISCLAIMS L l A B l L l N FOR ANY IMPLIED WARRANTIES. INCLUDING IMPLIED WARRANTIES O F 'MERCHANTABILITY'.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |